Get your audio codec with cat /proc/asound/card*/codec* | grep Codec Things I tried that made my speakers work but not the microphoneįrom No sound output devices listed after upgrade from 21.10 to 22.04 :Īdd options snd-hda-intel dmic_detect=0 to /etc/modprobe.d/nf and rebootįrom Ubuntu 22.04 does not recognize my microphone's headset when plugging in, just audio : Although I was always careful to revert changes I made when it turned out that they did not work, I'm not absolutely sure if the above is sufficient or whether it only works in combination with some other things I tried.Īudio Codecs: Codec: Nvidia GPU 94 HDMI/DP I also tried a lot of other things (see below). I could make the speakers work by installing firmware-sof-signed: sudo apt install firmware-sof-signedĪnd I could get the microphone working again by installing alsa-ucm-conf (from, Post #7): sudo apt install alsa-ucm-conf Neither the internal speakers nor the internal microphone were working and also external devices did not work. I had a similar error after upgrading from Ubuntu 20.04 LTS to Ubuntu 22.04 LTS. I checked the logs to be clean with: journalctl -b 0 -user-unit=pipewire -user-unit=pipewire-pulse -user-unit=pipewire-media-session -user-unit=init.scope (reinstalling rtkit did not work for me either) To /etc/security/nf (as seen here) to remove any error messages from the log. Remained and finally I also had to append - nice -20 Some reports in the Internet say you might want to create this directory before running the reinstall (which IMHO might not be needed)Īlthough audio worked for me after this, the error message mod.rt: could not set nice-level to -11: Permission denied Ls: cannot access '/usr/share/pipewire/media-session.d': No such file or directoryĪnd $ sudo apt -reinstall install pipewire-media-session For me a temporary solution was to run $ systemctl -user restart pipewire pipewire-pulseįinally I found that /usr/share/pipewire/media-session.d was missing $ ls -ld /usr/share/pipewire/media-session.d I have been updating & upgrading Ubuntu but still no fix. But if I unplug the headphones, I get no sound.Įdit 2: Well now I do not have sound anymore. $ pactl info | grep '^Server Name' Server Name: PulseAudio (on PipeWire 0.3.48)Įdit: After plugging my 3.5mm Headphones into the headphone jack and rebooting, I get sound over the headphones. The terminal doesn't complain but I also still do not have audio. Loaded: error (Reason: Unit rvice failed to load properly, please adjust/correct and reload service manager: File exists)Īug 11 08:58:40 thinkbook systemd: rvice: Cannot add dependency job, ignoring: Unit rvice failed to load properly, please adjust/correct and reload service manager: File existsĪug 11 19:27:44 thinkbook systemd: rvice: Cannot add dependency job, ignoring: Unit rvice failed to load properly, please adjust/correct and reload service manager: File existsĭoes seemingly nothing. Run 'systemctl -user daemon-reload' to reload units. $ systemctl -user status rvice Warning: The unit file, source configuration file or drop-ins of rvice changed on disk. Kernel modules: snd_hda_intel, snd_sof_pci_intel_cnl Memory at c1000000 (64-bit, non-prefetchable) Memory at c131c000 (64-bit, non-prefetchable) Subsystem: Lenovo Cannon Point-LP High Definition Audio Controllerįlags: bus master, fast devsel, latency 64, IRQ 16 $ lspci -v | grep -A7 -i "audio" 00:1f.3 Audio device: Intel Corporation Cannon Point-LP High Definition Audio Controller (rev 30) (prog-if 80) $ cat /proc/asound/modules 0 snd_hda_intel $ aplay -l **** List of PLAYBACK Hardware Devices ****Ĭard 0: PCH, device 0: Generic Analog Ĭard 0: PCH, device 3: Generic Digital I have tried everything: Rebooting, regular shutdown, apt-update, updating GRUB, trying to install pipewire/wireplumber/pipewire-session-media and see if that works, no luck. I have no sound on my ThinkBook 14S-IWL Laptop running Ubuntu 22.04.1 anymore. Thanks for general answer which will open new horizons and Miln though I'm not fond of AppleScript, but as requested here's my. However I encountered DNS problems when going from an internet interface to another (as WiFi to LAN Network) and thought that I needed to restart my OpenVPN daemon with launchctl to fix it.īut with this method I need to go to a console, type a monstrous launchctl's command with sudo and, of course, type my admin password.Ĭan this typing process be automated? Edit On OSX 10.10 I created a plist file in /Library/LaunchDaemons/ to start at launch an OpenVPN connection.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |